{ "id": "chrome-screw-in-shower-drain-cover", "sku": "chrome-screw-in-shower-drain-cover", "title": "Chrome Screw In Shower Drain Cover", "slug": "chrome-screw-in-shower-drain-cover", "price": 23.99, "currency": "CAD", "availability": "in_stock", "category": "shower-drain-covers", "category_label": "Shower Drain Covers", "tags": [], "colors": [], "materials": [], "dimensions": null, "weight": "45 g", "images": [ "https://ezydrains.net/dropship-images/shower-drain-covers/chrome-screw-in-shower-drain-cover/main-chrome-screw-in-shower-drain-cover.jpg", "https://ezydrains.net/dropship-images/shower-drain-covers/chrome-screw-in-shower-drain-cover/chrome-screw-in-shower-drain-cover-2.jpg", "https://ezydrains.net/dropship-images/shower-drain-covers/chrome-screw-in-shower-drain-cover/chrome-screw-in-shower-drain-cover-3.jpg", "https://ezydrains.net/dropship-images/shower-drain-covers/chrome-screw-in-shower-drain-cover/chrome-screw-in-shower-drain-cover-4.jpg" ], "description_short": "Made from 304 stainless steel in a chrome finish, this removable 4-1/4 in. (108 mm) round strainer screws down flat so water drains freely and hair stays out of the pipe.", "description": "The small part that makes a shower look neglected\n\nMost bathroom renovations start with the big stuff. New tile, a fresh faucet, maybe a better showerhead. Then you stand in the finished shower, look down, and there it is: the same rusty, chipped, discoloured drain cover that was there before. It is a tiny piece of metal and it drags the whole room down.\n\nThere is a practical side too. A drain cover that has lost its finish tends to catch grime in the pitted areas. A cracked one lets hair slip past into the trap. A warped one sits unevenly, so water gathers around the rim instead of running away. None of that is dangerous, but all of it is annoying, and all of it is fixable for the price of a takeout meal.\n\nThis guide walks through what a screw-in shower drain cover actually does, how to check whether a given one will fit your drain, and what to do when it arrives. It is a job you can do yourself in a few minutes.\n\nWhat a screw-in cover is and how it works\n\nShower floor drains come in two broad fitting styles. Snap-in covers push into the drain body and are held by friction or small tabs. Screw-in covers sit in a recess and are clamped down by a screw that runs through the middle into a threaded crossbar below.\n\nScrew-down is the sturdier of the two. It does not lift when you nudge it with your heel, it does not rattle, and it will not float out if water backs up momentarily. The trade-off is that cleaning means reaching for a screwdriver instead of just lifting the grate. Since most people only need to clear a floor drain every week or two, that is not much of a burden.\n\nThe grate's job is simple. Water needs to get through, hair and debris need to stay on top. The holes on this cover measure 0.4 in., which is on the generous side for flow and still small enough to gather most shed hair on the surface. Hair that sits visibly on the grate gets wiped away in seconds. Hair that slips into the trap builds up with soap into the sort of mat that eventually slows the shower to a trickle.\n\nGetting the measurements right\n\nThis is the part people skip, and it is the only part that really matters. Two numbers decide whether a screw-in cover will fit.\n\nThe first is the outer diameter. That is the width of the round grate itself, or the width of the groove or recess it drops into. This cover is 4-1/4 in. across, which is 108 mm. If your recess is 4 in. or 4-1/2 in., it will not seat properly.\n\nThe second is the screw hole spacing, measured from the centre of one hole to the centre of the other. On this cover that is 2-5/8 in., or 66 mm. Even a correct outer diameter is no use if the screw does not line up with the crossbar below.\n\nTo measure, take the old cover out first if you can. Lay it on a flat surface and run a tape or ruler across the widest point for diameter. Then measure between the hole centres. If the old cover is gone or broken, measure the recess directly in the shower floor and sight down to find the crossbar.\n\nWrite both numbers down. Compare them to the figures listed for any cover you are considering. If they match, you are good. If they are off by more than a millimetre or two, keep looking.\n\nWhy stainless steel and thickness matter\n\nThe material choice for anything that lives in a shower comes down to corrosion. Water, soap, shampoo and the occasional cleaning product make for a harsh spot. Plain steel rusts. Some plastic grates go brittle and yellow. The 304 grade of stainless steel used here is the common choice for wet environments because it holds up well to constant moisture.\n\nThickness is the less obvious factor. This cover is pressed to 14 gauge, which is 1.2 mm. That figure is a sweet spot. A thinner grate can bow in the middle when you stand on it, or dish slightly when the screw is pulled tight, and a bowed grate holds a shallow puddle. A thicker grate stands above the shower floor, which catches toes and interrupts the flow of water toward the drain. At 1.2 mm you get enough rigidity to resist deformation without sitting proud of the surface.\n\nThe chrome finish is applied by plating and then painting. That double process is what gives the colour staying power. It also leaves a slick surface, so mineral film and soap residue have less to cling to. The one caution from the maker is to keep bleach away from it, since bleach can lighten the finish over time. Dish soap and warm water handle normal cleaning without that risk.\n\nFitting it yourself\n\nAssuming the measurements line up, this is a short job.\n\nStart by removing the old cover. Back the screw out with a screwdriver that properly fills the slot, since a loose fit will round off the head. If the screw is stuck, run warm water over it for a minute and try again. A penetrating lubricant helps on badly corroded screws, and a little patience beats brute force.\n\nWith the cover off, take the opportunity to clear whatever has gathered in the top of the drain. A gloved hand or a bent piece of stiff wire pulls out most of it. Give the recess a wipe so the new grate seats on a clean surface.\n\nSet the new cover into the recess and turn it until the screw hole aligns with the crossbar below. Start the screw by hand so you know the threads are catching straight, then tighten with the screwdriver until the grate is snug. Snug, not cranked. Over-tightening can dish a thin grate or strip the thread in the crossbar.\n\nRun the shower and watch the water go. That is the whole job. If you are ever dealing with pipework itself, cutting, moving or connecting, that belongs to a licensed plumber, but swapping a surface cover does not.\n\nKeeping it looking good\n\nA drain cover rewards a little routine attention. Every week or two, back out the screw, lift the grate, pull away the hair, and give it a wash. Warm water, a drop of dish soap, a soft cloth and an old toothbrush for the holes. Rinse it, dry it, screw it back in.\n\nAvoid scouring powder and abrasive pads. Chrome scratches, and once it is scratched the dull patch is permanent. Skip bleach for the same reason. If hard water leaves white spotting, drying the grate after cleaning makes a bigger difference than any product.\n\nWe also steer people away from chemical drain cleaners. Clearing hair at the grate before it travels down is more effective, and it is much gentler on both your pipes and the finish on the cover.\n\nWho this suits\n\nThis cover works for anyone with a round, screw-down shower drain measuring 4-1/4 in. (108 mm) outer diameter with 2-5/8 in. (66 mm) screw spacing. That is a common size, but it is not universal, which is why the measuring step is non-negotiable.\n\nIt is a good fit if your existing cover has rusted, chipped, cracked or simply gone dull and you want the shower floor to look finished again. The Art Deco patterning gives it a bit more character than a plain slotted grate, and chrome coordinates easily with the chrome faucets and fittings that most bathrooms already have.\n\nIt is not the right part for a bathtub drain, which uses a different stopper setup, and it is not a snap-in replacement.\n\nThe short version\n\nMeasure two things: the outer diameter of your drain recess and the distance between the screw hole centres. If you get 4-1/4 in. (108 mm) and 2-5/8 in. (66 mm), this cover fits. It is 304 stainless steel at 14 gauge, finished in chrome, with 0.4 in. drainage holes and a removable grate that comes out with a screwdriver.\n\nFitting takes a few minutes and no plumbing. Clean it every week or two with soap and warm water, skip the bleach and the scouring pads, and it will keep doing a quiet job well.", "llm_summary": "A round chrome screw in shower drain cover made from 304 stainless steel, pressed to 14 gauge (1.2 mm). The outer diameter is 4-1/4 in. (108 mm), the screw holes measure 2-5/8 in. (66 mm) centre to centre, and the drainage holes are 0.4 in. across. The finish is chrome, applied by plating and painting. The grate is removable for cleaning and installs as a direct screw-down replacement for an existing round shower drain cover of matching size, with no plumbing work required. Listed item weight is 45 g and listed product dimensions are 10.8 cm by 10.8 cm. The style is described as Art Deco. Colour, country of origin and overall assembled depth are not specified by the maker.", "returnable": true, "return_policy": "Voluntary 14-day change-of-mind returns in original condition, buyer pays return postage; provincial consumer protection law for faulty goods. Return postage on faulty goods is ours.", "shipping_profile": "standard", "warranty": null, "brand": "EzyDrains Company", "gtin": null, "mpn": null, "condition": "new", "url": "https://ezydrains.net/chrome-screw-in-shower-drain-cover/", "canonical_url": "https://ezydrains.net/chrome-screw-in-shower-drain-cover/", "json_url": "https://ezydrains.net/api/products/chrome-screw-in-shower-drain-cover.json", "updated_at": "2026-10-12" }